HORESRAIL
®
– BASIC INSTALLATION GUIDE
JWI8765_HRBIG_1115
SAFETY FIRST: USE SAFETY EYE GLASSES AND GLOVES.
Horserail
®
is a registered trademark of John Wall, Inc. 2015
6
7
3
4
5
2
1
1
2
3
4
OR
OR
Attach brackets to line posts
A)
Find the center tangent of each
post - this will reduce binding
B)
Use a tape measure or a marking
board to locate and mark the top
of each bracket - from the top down
C)
Attach Top Line Post Brackets and
Line Post Brackets (one bottom hole only)
Install rail onto selected end buckle
and attach to end post
A)
Pre-Bent 45º Attaching Buckle attach at
a 45 degree angle leaving the lag screw
partially out
B)
OPTION: Straight Attaching Buckle - for
use on a flat surface such as a building -
Note: tighten the lag screw
C) IMPORTANT:
Do Not Overtighten!
Payout rail and insert into brackets
To best protect the rail - Use either a
“Payout Box” or an oversized spinning jenny
A)
Lift and slide rail in place
B)
Align Brackets to right angle of rail -
allowing for movement
Install other end of rail using the
proper end buckle
UÊ/¡}¢Ìi£Ê¤>}ÊÃVÀiÜÊ¢>¤vÜ>ÞÊ
UÊ=i>ÛiÊÃÕvv¡V¡i£Ìʤi£}̢ʡ£ÊÀ>¡¤ÊÌ¥Ê>¤¤¥Ü
proper tensioning - see Step 6
Use a Joining Buckle to join two
rail sections together
45
º
A
A
C
B
A
45
º
6
7
OR
Install Spooler and tension the fence
For aesthetics - place Spooler 12˝ (305mm) min.
from line post
A)
Place Spooler on rail and slide
“removable” hub piece into place
B)
Allow for one full rotation before
becoming taut
C)
Place locking pins into pre-drilled holes,
opposite each other, to stop the Spooler
from unwinding
Complete your fence installation by
fully tightening the lag screws from
Step 2 and Step 4 - this will also
further tension the rail!
UÊ
IMPORTANT:
Do Not Overtighten!
BRACKET SCREWS:
Use Wide Shoulder
#8 - 2˝minimum; 5/16˝ (#8 - 50mm minimum; 8mm)
Hex Head Drive Screws Only
LAG SCREWS:
1±2˝ x 4˝ thru 6˝
(12mm x 100mm thru 150mm)
BENDING TOOL:
for Simplicity and Neatness
The perfect tool for bending rail to the optimum
shape and dimension
LONG HANDLE RATCHETS:
Used for a “Two-Man” Installation Process!
EXTENDED HANDLE RATCHETS:
Used for a “One-Man” Installation Process!
A
B
C
HARDWARE AND ACCESSORIES
5
Finish attaching all brackets
to line and end posts
UÊ1ÃiÊv¥ÕÀÊÜ¡`iÊâ¥Õ¤`iÀ]Ê¢iÝÊ¢i>`
drive screws for each bracket
UÊ)À>V¦iÌʧÕÃÌÊLiÊ>ÌÊÀ¡}¢ÌÊ>£}¤iÊÌ¥
rail - allowing for movement
For More Details, Tips & Techniques on Building Fences,
Please visit our website:
www.horserail.com
Just – buckle it up!
Patent Numbers: 6,533,881; 6,431,487; 7,566,047 and Other Patents Pending